Meet the

Advantages

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Valve Fillpro

It is the valve that allows the entrance of water to the tank and valve FILLpro, has the following features.

Do not use float or rods.

It runs from the bottom of the tank, based on diaphragms.

Made of high quality non-corrosive materials: polypropylene and stainless steel.

Works with a wide range of pressures, from 0.2 up to 12.0 kg/cm2 kg/cm2.

Avoid water hammer.

Controls the level of water in the tank with high accuracy using a set screw.

By its precise regulation, avoid the spill of water through the overflow tube, avoiding leaks at all times.

Great fast installation, because that requires no tools or sealants for placement.

Easy to maintain, is not required to remove it for service, which is not often performed.

Proudly distributed by:

logo_O_222x75

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Specifications

The recommended range of working pressures is 0.2 kg/cm2 12.0 kg/cm2, hydrostatic pressure. FILLpro valve operates successfully with pressures of up to 14.0 kg/cm2.

It has been subjected to test cycles of approximately one million download without any fault.

The FILLpro valve has an estimated time of 152 years. We do this calculation under laboratory conditions, whereas an average of 18 downloads in a 4 member family and having tasted that valve has failed fault in 1,000,000 downloads.

The valves are manufactured with polypropylene white high quality, steel 18-8 stainless and black rubber.

All valves are pneumatically tested at factory at the time of be assembled to ensure a product of the highest quality.

It has been put special care in the packaging of products. Each one is inspected after being packed to ensure a consistent appearance, ensuring that all components are included in the package.

The advantages over products that exist in the market are diverse, but mainly due to the materials that comprise them.

Polypropylene that manufactured valves FILLpro, unlike the PVC, the celcon and bronze, is a thermoplastic that is perfectly suited to the use of the valve for the following reasons:

It can be modeled by injection method to produce a piece of high quality, high strength and excellent surface finish.

It is not corrodible and resistant to the attack of chemicals commonly found in water.
Thanks to its low density parts made of this material weighing approximately 1/7 of which would weigh the same piece made of bronze. 

The specific weight of the bronze is 8.4 8.7 while the specific weight of polypropylene (40% Talc Filled Propilene) is 1.23.

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Principles of Operation

Entry for FILLpro toilet tank valve is a device operated by a servo mechanism that uses the hydraulic force of the water supply to obtain positive of the main valve opening and closing.

(02169) inlet valve measures the level of the water through a diaphragm responds to the strap on it. The movement of the diaphragm operates the main valve which controls the flow of water into the tank.
mm0igplomeria_fillpro_valvula_principios

The diaphragm is attached to a lever that rocks on a shaft guide.

The adjustment screw and its spring provide a counterforce to the diaphragm, so a rolling of the lever action takes place according to the changes of the water level inside the tank to allow the closure of the pilot orifice that controls the opening of the main valve. The main valve is a disk of deformable rubber that has a camera control over it and a self-cleaning limiter in its Center. The change of pressure in the control Chamber head provides strength to the movement of the valve.

When the pilot hole is open, the pilot seat does to reduce the pressure in the control Chamber and the inlet pressure moves the main valve to the open position. When the water level rises in the tank, it acts on the diaphragm until it overcomes the force that the spring exerts. The seat-pilot closed the hole and the camera control is filled through the restrictor, thus closing the main valve.

The 18-8 stainless steel alloy, used in all metal parts, prevents galvanic corrosion even if immersed him in salt water.

This valve rubber moving parts have been molded with EPR specifically formulated for hydraulic service, reason why he was chosen to form part of the product.

All selected plastic materials are widely used in components of the highest quality plumbing and hydrosanitary service industry. In short, this valve of new technology, will provide many years of satisfactory service.

 

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Discharge Flap Jack Pear

Features:

Made of 100% vinyl, which makes it completely different from any other PEAR that exists in the market.

Vinyl is a very soft material so the FLAP JACK deforms easily molded to the Contras and avoiding water to leak.

It retains its elasticity at all times, regardless of the temperature of the water.Flap_diagrama1

Manufactured in one piece, so never again having problems with the wires or chains, that break away or lock prevents a proper discharge of the toilet tank.

Proudly distributed by:

logo_O_222x75

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Specifications

Discharge Flap Jack PEAR (00011) has an average life span of 9 years and a half.

Vinyl that makes up to download PEAR is other thermoplastic material, which also is molded with the method of injection and produces a high quality piece.

Flap Jack PEAR is the element of a control valve for water seal and adapts to any seat either plastic, bronze or other, no matter which kind of against that use. Its design ensures that the pressure of the water in the tank provides the sealing force.

Material ensures deformation and molding against which will provide efficiency in operation.

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Meet the

Principles of Operation

To be in the position of rest (in contact with the Contras) PEAR presents little floating, as well, to be covered by water and as it increases the strap on it, is deformed, molded to the Contras, obtaining a more perfect seal. To avoid excessive deformation in PEAR, radial reinforcements have placed him.

The PEAR has a camera with a hole in the bottom. When the PEAR is in rest position, this camera is filled with air, since the water drains it into the bowl, and air enters through the toilet overflow tube

At the time of the lever of discharge, PEAR changed position presenting little resistance to water that acts on it.The finding of the Chamber filled with air flotation this makes PEAR to float (staying aligned to fall back into its position thanks to the runners that attach it to the overflow pipe). To lower the water level to the PEAR, this descends with him until the moment in which the Chamber is flooded due to the angle that falling until the tank is emptied completely, which provides an additional water savings.

 

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Easy

Installation

Shut off the water to the tank and pick up the remaining water with a sponge.reductor_flujo1

Unscrew and remove the nuts (A) and (D). (FIG 2)
Remove the old system

TO INSTALL YOUR VALVE FILLPRO ® (FIG 2)

In the designated order, install new coupling (A), the corresponding gaskets nut (B) and (C) for 0.95 cm (3/8″) or only (C) feed for feeder of 1.27 cm (1/2″), the mounting nut (D) into the feed tube.

Set FILLpro ® valve at the bottom of the tank so that the screw (E) exit to the outside through the corresponding hole.

The black gasket (F) must be inside the tank.

Tighten the nut (D) on the screw (E). Hand tighten the nut (A) over the corresponding gasket (B) or (C).mme0plomeria_fillpro_pera_fig2
Warning: Hand tightening is sufficient, the over tighten can cause rupture of the tank or the nuts.

Insert reducer flow (G) at one end of the black line and set it on the edge of the overflow.

For decrease the flow reducer onto the hose.

Place the end of the pin (H). (FIG 1)

Open the stopcock.

REMEMBER THAT IT IS NOT NECESSARY TO USE ANY SEALERS OR TOOL.

FILLpro ® valve is adjusted to fill a tank to its normal level. To save water in each download turn the screw marked “ADJ” mme0plomeria_fillpro_pera_fig3in opposite direction to clockwise (fig. 3).

If you want to raise the level of water turn the screw in the clockwise. (FIG 3)One full turn will modify the level of water approximately 2.

IF YOU WANT TO SEE THE INSTALLATION VIDEO, CLICK HERE



THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Giving

Maintenance

Devices that work with water occasionally have problems due to impurities that are in the same.

If the valve does not close completely, follow this service procedure.

Turn off the water, flush the toilet tank and remove the screws from the top of the valve.Valv_Fillpro_Manten11

Open the cover with your fingernail, you will find two black discs, one large and one small or a large black disc and one small red (Fig. A).

With your fingernail carefully remove the small black (or red) drive from the top of the valve (fig. (B) so not to damage the white pole protruding from the lid since if this happens the valve already it will not work correctly.
Valv_Fillpro_Manten21

Clean the disc and place it again with the smooth side up (facing) or if necessary replace it with disc no. 11505 on sale with your dealer.

Reassemble the valve carefully assembling the mechanisms of union on the back of the valve (fig. C. make sure that the two sections of the valve coincide.

Check that the large black disk is placed instead and it sits perfectly by around the edge of the valve cover. Place screws (do not tighten more).Valv_Fillpro_Manten31

Turn back on the water and check that drip valve onto the floor there is no on the outside of the tank. 

If it came into existence drip onto the floor means that large black disk (IRIS) was improperly placed or bent. 

You must repeat the previous step.

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Easy

Installation

FOR CONS OF BRONZE TRADITIONAL TYPE:

1. Turn off water and flush tank. If you are replacing the old system remove thewires (B) and (D), guide the PEAR, and (C) (A). If you are replacing an old flapper (of string), slide up the ring (E) (F) overflow pipe.Flap_11

2. Wet ring (E) on its new, Flap JackÒ and run it through the tube of the overflow (F) with the curved side facing down (G), slide it until the ring touches the base of the overflow pipe.

3. Now, centre part, curved with the center of contra.Flap_21

4. Insert tape (J) on the last hole of the rod and pull it until it is a little slack in the tape when the Flap Jack this at low position or lock.

FOR THE NEW CONS OF PLASTIC WITH “EARS”

5. Cut its Flap Jack ring (E) on the lines marked with “CUT”

6. Slide the ears Flap Jack in the outgoing (F) overflow tube (L)

7. Connect the tape as explained in point 4.Flap_31

Flap Jack closes using the top edge of the cons of bronze or plastic. This must be free of burrs so that it seals well.

Flap Jack is guaranteed by Orestia for 3 years against manufacturing defects..

IF YOU WANT TO SEE THE INSTALLATION VIDEO, CLICK HERE

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Without leaving

Purchase

ll the products FILLpro in one place and in one click, purchase online in the comfort of your home.

We deliver to all the Mexican Republic and discover more products we have for you.

Only your home click on the image, and Renueva your home.

renueva

THE HIGHEST TECHNOLOGY IN YOUR HEALTHCARE FURNITURE

Stay in

Contact

SEND MESSAGE